Ultimate LS Torque Plus Composite 600HP Kit

$1,745.00

Add to Wishlist
Add to Wishlist
Part No: 70019 Categories: , Tags: , , , , , , , , ,

Description

The Ultimate LS Torque Plus Cathedral Port Composite 600HP intake manifold kit with cable operated 92mm throttle body are self-tuning systems for LS engines designed for the do-it-yourself hot rodder to the professional EFI tuner!. This intake manifold is an O.E. replacement quality reinforced plastic composite material combined with our top of the line Ultimate LS ECU. This self-learning dual wide-band Ultimate LS ECU replaces the OEM computer and harness. This new design gives your engine bay the factory O.E. look while giving you all the great features of our self-learning ECU, maximum tunability, and ease of installation. They’re simple to configure with the supplied color touch screen hand-held controller and can be used to monitor in real time or can be disconnected when the configuration is completed. It’s never been easier to swap a LS into practically anything you want with our stand-alone Ultimate LS kits. Suitable for that junkyard 5.3 to a stroker 427, we have you covered! Check out the list of features and you will wonder why it’s never been so simple to ditch that old factory hardware.

Application: Intake manifold will fit Cathedral Port LS1/LS2/LS6 heads.
Small Block V8 GEN. III/IV LS-based Chevrolet street and performance engines with a 1500-6500 rpm power-band up to 600 HP to the flywheel and contains a 3 BAR MAP sensor for power adder applications that supports up to 30 PSI of boost.
  4.8 L / 293 c.i. LR4, LS1 LS2 LS6, V8 Camaro/Corvette
  5.3 L / 325 c.i. L33, L59, LM4, LM7, V8 Camaro/Corvette
  5.7 L / 346 c.i. LS1, LS6, Cadillac CTS V, Pontiac/GTO/Trailblazer SS/Firebird/Trans-Am, SSR, Corvette
  6.0 L / 364 c.i. LQ4, LQ9, LS2, V8 Camaro/Corvette
Intake manifold height is 8 inches.
92mm high flow cable operated throttle body.
Throttle body will clear most stock truck accessories depending on the type of water pump, if there is truck water pump accessory clearance interference you will need to get a new water pump bracket. Water pump may need to be clearanced.
Parts required, not included:
  Coil packs
  Supported Fuel System (ie. FiTech part number 40004, 40005, 40007, 40015, 40019 or other comparable fuel systems).
Optional, not included: throttle cable mounting bracket (FiTech part number 70063)
Not legal for use on pollution controlled vehicles: FiTech’s Ultimate LS System is not CARB approved for use on emission ontrolled vehicles. This system is designed to control the EFI and ignition on LS based engines being retrofit into older vehicles that do not require emission controls.

Prop 65

Features

Low Profile, 92mm inlet, Cathedral port composite intake manifold with 1500-6500 rpm power-band up to 600 HP to the flywheel and contains a 3 BAR MAP sensor for power adder applications that supports up to 30 PSI of boost.
Re-enforced plastic composite material withstands extreme temperature from any engine bay.
Billet Fuel rails with AN fittings and fuel crossover.
Self-learning ECU with touch screen controller for easy setup and configuration.
Sequential fuel and spark control with individual cylinder trim.
Bosch wide band controlled (Self-learning).
Stainless O2 Sensor bung (clamp or weld on).
24X and 58X crank and cam compatible.
1 BAR MAP, TPS, and IAC Sensor mounted on intake.
Tach output driver for most tachometers (5V).
Output driver for most speedometers.
Compatible with car and truck coils.
On the fly programmable target AFR and timing (if desired).
55 lb/hr flow-matched injectors.
Fuel pump relay output.
Plug and play custom wire harness (uses factory coil pack sub harness).
Knock sensor control.
Tight-Fit EFI fuel pressure regulator & 0-100 oil filled guage.

Kit Contents

92mm cable operated billet aluminum throttle body.
Re-enforced plastic composite intake manifold and hardware.
Plug and play primary wiring harness.
Hand-held controller with color touch screen.
Hand-held controller cable.
Mini USB cable.
Windshield mount for hand-held controller.
LS ECU.
55 lb/hr Injectors.
High volume fuel rails. Fuel rail contents:
 
  Mounting bracket.
  -6 AN fittings.
  Rails.
  Screws to mount brackets.
  AN fittings and fuel crossover.
3 BAR MAP Sensor.
Billet MAP Adapter.
Throttle Position Sensor.
Idle Air Control Motor.
Idle Air Temperature Sensor.
Wide band O2 Sensor.
Stainless Oxygen Sensor bung kit (Clamp or weld on).
Tight-Fit EFI fuel pressure regulator.
0-100 oil filled guage.
Parts required, not included:
  Coil packs
  Supported Fuel System (FiTech part number 40004, 40005, 40007, 40015, 40019).
Optional, not included: throttle cable mounting bracket (FiTech part number 70063).

Additional information

Shipping Weight 32.6 lbs
Shipping Dimensions 28 x 16 x 10 in

Tech Manuals

Ultimate LS Induction Systems Product Brochure

Download

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.